I was all set to write up the pattern for my amigurumi bunny scarf, to go with the amigurumi bunny kits I make, but we had such unexpectedly lovely weather at the end of February that it no longer seemed appropriate (though I will get round to doing this in the future).  Instead, I decided to design a top hat to go with my amigurumi cat kits.   It took me a lot longer than I anticipated – I decided to take photographs to explain parts of the pattern so it’s more of a thorough job than I originally intended!

So here it is!  I hope you like it!

 

Stovepipe Hat

A free accessory pattern to go with my amigurumi cat kits

Key – UK crochet stitch terms used

htr – half treble                       dc – double crochet
ch – chain                                BLO – back loop only
ss – slip stitch                         FLO – front loop only
st/s – stitch/es

For this pattern I used Stylecraft Special Chunky and a 4mm hook 

R1:  Make a magic ring, ch1 and crochet 9htr into it, join with a ss to the first htr made

      

(Click here to take you to my how to make a magic ring tutorial)

R2: ch1, 2htr in each st around, join with a ss (18 sts)

R3: ch1, dc in BLO of each stitch around, join with a ss (18 sts)

  

Instead of going under both loops of the ‘v’ as you usually would you go through the back loop only.

(if you haven’t crocheted over your initial end then now is a good time to sew it in)

You end up with the front loop making a ridge and you’ll now be crocheting up the sides of the hat.

R4 – 8: ch1, 1htr in each st around, join with a ss (18 sts)  This row is repeated 5 times

    

R9: ch1, dc in FLO around (18 sts)

   

You have how changed direction again and will be crocheting the rim of the hat

R10: ch1, 2htr in next 9 sts, turn (18 sts)
(check the hat on your cat’s head to see if this a good size, as you can see for me my cat’s ears are roughly central so 9 sts works, you may have to adjust for your own cat)

            

R11: ch1, 1htr in next 2 sts (the first of these will go directly below the ch1 you just made.  I’ve put a wool needle in the space to show you), then 2htr in the next st (repeat the pattern of 1htr, 1htr, 2htr till the end of the row) (24sts)
fasten off.

         

Now you’re going to make the front on the hat rim.

To make space for the ears you need to miss a stitch out on each side.  So join the yarn one stitch in, in the 2nd picture the yarn needle shows you the missed stitch and the crochet hook shows you where to join.  On my hat I have 7 stitches to crochet into.

   

R12: ch1, 2htr in the same place as the join (shown where my yarn needle is again) then 2htr in the next 6 sts (or as many as you need for your hat making sure you leave the last st empty) (14 sts) turn.

   

R13: ch1, 1htr in the next 2 sts (again the first stitch you go into is shown with my yarn needle), then 2htr in the next st (repeat the pattern of 1htr, 1htr, 2htr till the end of the row) finishing with 1htr in the last 2 sts (do not turn) (18 sts)

   

R14: ch1, then 1dc around the whole of the hat brim being careful not make the stitch that jumps the gaps too loose.  Join to the 1st dc of the round with a ss and fasten off (42 sts)

         

Weave in the ends.

Lastly pop it on your cat’s head!  Ta da!

      

 

I hope you enjoy making your top hat for your cat!

Vicki x

P.S.  You can find my amigurumi cat kits in my Etsy shop and also at Quillies a bricks and mortar shop in Rhayader, mid Wales; Talgarth Mill Craft Shop, Talgarth and The Wyeside Arts Centre, Builth Wells.